Best Dealerships To Work For (2025 Updated)

Have had the unit for about a month now and man I love this thing! Definitely has improved my workflow by quite a bit. I have a number of hobbies that I cycle through throughout the season and according to my wife I have an overabundance of tools (like that is possible!).

I have a 52″ chest in a detached garage and a smaller 27″ combo box in our attached garage and even with all that storage space I was getting crowded. As well in the detached garage where I do most of my work, the garage is separated – one side is insulated while the other is not.

I keep the 52″ chest in the insulated side to protect batteries and electronics while most of the work occurs on non-insulated side. As you can imagine this creates a lot of extra walking, going back and forth to grab the right tool.

Enter this 5-drawer cart. All my most used tools go in here and my tool journeys have been cut by at least half. It’s well organized with lots of thoughtful accessories that enhance it even more. Magnetic strip on inside of top lid holds an assortment of wrenches.

Towel holder, glove dispenser, and magnetic tray holders sits on the sides. It’s opened up 5 drawers in my 52″ chest with a full drawer leftover still and basically is a one stop shop for most repair work.

The optional side tray is also a great addition for staging. Such a time saver! The screwdriver organization is a nice built-in feature but identification of the right screwdriver is hard. Wish the top section was just a bit taller to accommodate long-handled pry-bars.

Assembly is easy and straightforward but you will want an extra pair of hands to hold things in place for you and while placing the top onto the frame.

Purchased this cart for my business partner as a Christmas Gift. Looking at the value, there was no question, but upon assembling it for him i took notice that the inside of all the cabinets were all fully powder coated, not a single nook and cranny, crack, space was uncovered with powder.

That compared to the husky which cannot make that claim. Seen all of the husky’s in the store and each one had NO powder coating on the inside, take a drawer out and you will see the only powder coating inside is what over spray missed the front and sides and ended up settling in the cabinet.

That also you see will see plenty of surface rust because it was not covered. ALL of the harbor freight boxes have the same perfect finish inside that they do on the outside. Also the Home De brands seem to never brush out rivet nails, un-crushed rivets, and other little trash pieces in corners that gets stuck in the powder coat over spray.

I am sorry, If I am paying a few thousand dollars for a monster toolbox, I want all steel wheels, boxes that wont buckle when we all overload each drawer. Lets face it, if it fits, it sits. is all of our mind sets.

If you can fit every socket in one drawer you own, you will put it all in there, not ONE of us thinks, HUH maybe I am overloading this box and sit there doing math and weighing each socket set you own, and looking at the manual to see what each drawer can handle HELL no, You toss it in there and if it fits, it sits there forever.

We are all guilty of that. So these carts I got one for my partner for the shop and he ended up loading about 80% of his tools into the cart and drags it around the shop over cords, dirt, bolts, nuts washers, everything on the floor and it has a very sturdy feel and sound to it, not tingy and thin but thick, solid, and durable.

I airbrushed the lid and the powder coat made a phenomenal base coat for the self etching primer I used and since it was thick powder coat, I did not have to worry about what type of paints I used and upon finishing the airbrush work, I clear coated it and it came out as good as any car Ive ever painted.

I loved his cart so much I decided to buy one for myself. I again airbrushed mine and loaded it up with my stuff and drag it around all over the shop like he does. Not only did I love it so much I just purchased a monster green 72 inch roller cabinet and 72 inch top box and will be buying a third YES THIRD tool cart, which I plan on sandwiching in between the top and bottom on the left side and use the angle steel/iron corners to hide the pipe support and flanges to hold up the top box and use the bottom shelf as the right side cover, ill use PEG board on the back or slat board and 1 or 1 1/2 inch pipe and flanges to hold up the top and bolt it down to the underside of the top with a piece of 3/4 plywood under the top box and on top of the bottom box to distribute the load/weight of the top and do a make shift hutch for my laptop and put some lights and other things in there as well as storage for awkward bulky items that are too big for any drawers.

Since It will be the same Green as the monster 72 inch top and bottom i am hoping it looks like this makeshift hutch was meant to be this way and since I plan on bolting everything together so nothing can move or shift, the only thing is ceiling heights I have to be concerned with.

I will post photos of that project upon completion but for now, a few shots of the tool carts I bought for my business partner and myself are below. I cannot stress how well built and how well these handle the day to day abuse of professional and semi professional and weekend warrior home users, the price point makes it a no brain er, but what you get in the long run is a box that will last you an easy 50 plus years for a 200 dollar-ish price point, Why would you NOT buy it and put it through its paces, I promise you, you will NOT EVER be disappointed with its quality performance & durability and the powder coating makes it last forever and it wont ever rust which those other brands that only have a minimal over spray inside the cabinets, can NEVER say that.

Go to Home Depot, go grab a drawer and pull it out of the box and look inside, you will see a lot of surface rust, broken rivets, rivet nails in the corners, in any Harbor Freight box, you will pull a drawer out and see the same perfect finish inside that you see on the outside.

THAT right there shows that even if its made outside the USA they CARE about their workmanship & know what their customers expect and demand. Everything I have purchased thus far has all lived up to the same high quality and durability and great fit and finish that I would put it up against any Snap-On, Matco, Mac box out there.

The ICON line is even more fantastic but since I am not a F/T pro mechanic, I don’t see the need but if I was still full time you can be sure id own a full ICON setup no question! Thank you Jennifur.

Instructions were pretty vague. Putting together this cart is a good test to determine your skills and patience. DO NOT tighten things other than the casters until you set the chest on the cart. You will be redoing things if you did.

Getting some of the carriage bolts to grab on the square holes was challenging at times. You will need some decent tools to put this together. If you think you’re going to get it done with an adjustable wrench and a pair of pliers, good luck.

The cart, once assembled, is awesome! It’s perfect for some basic tools for the average DIY garage. I use the top for 1/4, 3/8, and 1/2″ sockets ratchets, and extensions. Top drawer on left is screwdrivers, next is pliers.

The upper right drawer is plastic bins with smaller tools, bits and such. First full drawer is wrenches. Last drawer is deep and I use it for hammers, punches, chisels, wire brushes, and other oversize items.

The bottom of the cart is perfect for those blow-molded cases that hold power tools and such.

This machine was supposed to be an upgrade from my basic model but I would give anything to have my old machine back. At least it could handle more than 2 layers of fabric. I had never broken a needle in my 10 years of sewing until I tried using this one.

Broke the first needle within 30 minutes of using the machine. It’s supposed to be good for quilting but I just broke another needle (the 5th since owning this machine) while trying to sew the backing, batting, and top layers of my quilt together.

I changed the needle and rethreaded top and bobbin, now it doesn’t work at all. the Needle keeps getting hung up on something inside and jamming. It’s a shame that I’ve had it for 2 months and have only used it a handful of times.

Save your money and by the basic sewing machine models, you will be much happier.

I was so excited to get this machine, did my research and it arrived promptly. I am not a beginner but read all thru the booklet anyway. I am beyond disappointed! The tension refuses to cooperate which causes broken thread.

The various decorative stitches either do not work at all or change in the middle of a project!! When you adjust the speed to a certain level, all of a sudden it speeds up by itself. Lighting is poor.

Very noisy. I paid to have maintenance done by a reputable company after only a month and that did not correct anything! After having to take a project apart 6 times yesterday. I am over this machine.

Its brain has gone berserk! I have had the machine 4 months, done everything the manual says to correct these issues and now am told they don’t stock it anymore so. no replacement. I now have to pay to ship it back plus a restocking fee.

Why would you restock a machine that does not work? I would gladly have accepted a new machine of the same kind, thinking this one is just defective. No cooperation there. Against “policy”. I guess they worry more about policy than making a customer happy.

Buy this machine at your own risk. Mine was not right from day one. So I lose for trying to do what I could to work with it.

So I read the reviews on cs6000i. Actually the reviews are why I bought this machine. The machine is broken. I heard about how great their policy on fixing and such. So I call Brother. The hand wheel seized up and there is oil in the bottom of it.

Now I am told that I can take it to a sewing center to be fixed. I might add that is 30 minutes away so they can fix it. I may or may not have to pay for it. It may or may not be covered under warranty.

Soi have to say I won’t purchase again based on customer service. The machine has only been in use for 2 months. This makes me sad at the least.

This work order/invoice book is great for smaller jobs that do not require a lot of material to be listed or a lengthy description of the work done. It gives you a 3rd copy for your However, it gives you only 9 boxed lines for material on the front and a small box for the description.

If the material lines were a little less tall they could have fit 10 to 12 lines which I find to often be necessary. If the very bottom section of the page for estimates were made just a little smaller this would also free up some more space as well.

The estimate section is seldom used in my experience and can be easily incorporated into the description. The print on the back is way too faint and it won’t transpose to the other copies when you use it so I find the back useless and never use it.

Overall though, I like this book for billing most of the time.

This work order book is a good invoice book that gives you 3 copies of what you write out. It gives you spots to write whatever pertinent information you need like customer phone and address, what’s being serviced, 9 lines for parts used, and a description box of what was done.

There is also blank space up top to write the business name. The yellow copy I give to the customer while retaining the original top copy and the thicker white tag copy. I would have preferred more spots for parts used but this is only sized roughly 5 1/2″ x 8 1/2″ so room is limited though they could have made the spacing slightly tighter for 10 to 12 lines for parts.

Overall, this is the invoice book that I normally use and I am generally happy with it.

We have used these for years. The 3-part allows us to send one copy to the customer and keep one for our tax records. The third copy we keep in case the customer loses their original copy. Plenty of room to write down materials used for the job, and the extra space on the bottom leaves us enough room to put in our labor hours.

The book holds together well at the top. We’ve never had trouble with it falling apart. Highly recommend this top quality product!.

I was about to give up on my new Brother ST371 sewing machine – it seemed to have the same problems as my Project Runway machine – ‘bird nesting’ on the bobbin, broken stitched, uneven stitching. But after talking with an experienced quilter and explaining my broken seams problem, she helped me through.

It is important to change the needles frequently (I change mine every couple of projects) and make sure you are using a good quality thread that ‘matches’ with the fabric you are using. In the beginning, I was skipping these steps – my old Kenmore machine was a victim of my ignorance.

Since using the tips from a ‘quilting pro’, I’m happy with my ST371 machine – it has all the stitches I’ll need and I’ve bought various ‘feet’ to help increase this machines usefulness. I am mainly a hobbyist and have tackled cat beds, Halloween costumes, and clothes for family members with good results.

I don’t whether or not these people are doing what they are supposed to be doing or that they just don’t know how to use the machine. I have been sewing since 1968 and have used a lot of sewing machines.

I own a Bernina 1090QE, a Bernina B480, and my little workhorse ST371HD machine. I can’t say anything bad about my Brother ST371HD. This machine is a very good sewing machine. I went for like 15 years without sewing and did not have a sewing machine.

I bought this one just to make bedroom curtains for my house. After getting acquainted with the machine, I was bowled over by this machine. I LOVE IT!!.

Bought about a year ago. Purchased this brand because that is the brand I learned to sew on and loved that machine. This machine however, I fight with. Maybe bacuse It’s “new and improved. ” I find the lever to lift presser foot to be in the most awkward place.

Inside right side, instead of readily available on the back side, more convient to access, instead you have to reach through the middle of the machine. Why would they change that? For the sake of change I guess.

Also not a fan of the storage compartment, not easily taken off or put back on. In addition, the cord that goes to the outlet is about 6. 5 feet long and the cord that goes to the foot pedal is about 4′, a little short if you don’t want the cord hanging down in your lap and work area ( I’d rather it be long enough to pass toward the back of the table down to the floor) and plugs in on the side, why not the back out of the way of work areas??, Over all I found this machine to feel cheaply made (all plastics), but again my first brother the base was more metal like, while the top was plastic it just felt more solid.

I have trouble with the bobbin knotting up at times. I guess I don’t have the tension set correctly all the time? I am of course comparing this to my first Brother machine that had hundreds of hours on it.

(I’m not exactly a beginner) Maybe had I learned on this one(BrotherST371HD) I would like it better. Would I recommend for your first machine, I’d say give it a try, you have nothing to compare it to.

But highly recommend IF you can go in store to try other models and brands do that!.

Exactly what I am looking for to identify and track my products when I ship. The brick and mortar store where I used to buy them no longer carries them. In fact, they don’t carry anything close to this with all the relevant information.

So I was very happy to find them on the manufacturer’s web site!.

The product seems to be good but the advertising is not. It said five books for that price ,and it was only one. I was disappointed because of that.

WE REALLY LIKE THEM FOR OUR CUSTOMERS. JUST WISHED THEY MADE A 3-PART.

I bought myself a heavy duty machine to replace my previous singer. After much consideration, I went for the Heavy duty model as I previously found my old machine couldn’t tackle thicker fabrics such as wools for coats.

The online support service was brilliant, very knowledgeable and didn’t push you to buy a model that was more powerful than your needs. I even got some extra bits and bobs! The delivery on the machine was incredibly quick.

It’s a great machine, so quiet in comparison to my old singer! The first project was a canopy with a very heavy canvas, sewed like a dream. Can’t wait to use it more as winter sets in and we update our family wardrobe.

Best buy I’ve made!.

I’ve used Singer sewing machines for the last 50+ years. This model was an extreme disappointment. It is in no way ‘heavy duty’. It sews faster than previous sewing machines and that’s about it. It won’t sew through the same things the previous machine (purchased in 1992) sewed.

This one is a complete waste of money. I’ve communicated with Singer several times about this and the nearly useless Serger I bought at the same time, and at no time did they say they were looking to improve on their current models.

If you want to sew two pieces of lightweight material together and nothing else, this machine will probably work fine for you.

This machine does exactly what it says. For my first project I’ve already sewn 6 layers of leather together and also multiple layers (4) of Harris Tweed, to make a handbag. Despite being a very novice sewer I haven’t found any real difficulties, although there is definitely a “knack” to catching the thread from the bobbin, but once mastered it really is quite straightforward.

Not a quiet machine, but when it’s dealing with heavyweight fabrics that’s understandable. I would recommend a walking foot as an optional extra, plus some spare bobbins and heavyweight needles. I definitely recommend this machine.

This Carlon outlet box is the type that has two small “wings” on the back that will flip open and extend behind the drywall as you tighten the facing screws. So this is the box to use when you want an outlet in a location without a nearby stud.

I was a bit skeptical of mounting a box in what was basically a small hole in drywall, but this box really gripped the drywall and stayed put. I was able to do my wiring without any hint of box wiggle.

Now ideally I would want my box to be attached to a stud, but with some remodeling projects you just can’t always have it that way. I highly recommend this Carlon box for those situations. By the way, ACE also sells a variety of other Carlon box sizes that work in the same way.

Over 30yrs in telecom and a/v contracting taught me that you go with what works. This “old work” box is nothing special. No whiz- bang features or fancy function. It just does what it’s meant to do. Everytime.

Easy to use and helps get it done right the first time.

With this box, you don’t need to secure to a hidden stud behind the wall. Just cut drywall out at any place on the wall, tighten screws to secure box to drywall, and run wire through box.

I had bought a 3-part book a year ago and had finally gone through it. I knew I didn’t need 3-part and was happy to be able to get 2-part and in a little bigger book. And not having the carbon sheet is so much easier! When this book gets used up I will buy again.

This is perfect for any quick Sale as you are not fumbling with Carbon Paper. Customers appreciate not having the Carbon Paper stain.

I have been buying this product for over ten years and never been disappointed. It is consistently of high quality, and is a perfect fit for my business needs.

I know these are good for ‘everything’ but they have completely elimated the need for disposable wipes in this house. We use them for daily intimate care for a handicapped man. They don’t break down when wet, can hold a ‘bundle’ (If you know what I mean!), yet remain soft.

I can even rinse them out and reuse to get a good clean. I even a fold a few into a plastic bag, moistened, when we go outl. ujMuch better than disposable wipes!.

I really LOVE this product. It soaks up extremely well. I am a painter and only ever need to use one towel at a time. Sometimes one for a few times. I usually go through a ton of normal paper towels but I never have to with these.

I use them for cleaning as well. They work like a cloth and last quite a while. I love them. I’ll never buy paper towels again.

Have been using these for many many years & would Always give a 5 Star. The rolls are now smaller & being made of lesser quality. Whereas I used to be able to use a sheet multiple times & rise it out (for dusting), it now falls apart in the first use.

So disappointing. Please charge more, BUT DON’T give a lesser product due to inflation. I may as well buy a cheaper brand.

I purchase one of these about a year ago was hopeful I would be satisfied at such a modest price. As soon as I opened the packaging and inspected the product I was surprised by the quality of the chest.

It was simple to assemble and all the fasteners easily fit every threaded hole without the usual force or modifications required which I have run into with other brands. Several months later I needed additional storage and immediately ordered the same one again.

Both arrived well packaged and without so much as a scratch. Amazing value!.

I purchased this tool chest about 2 months ago. At first it seemed like it wouldn’t lock but then I realized that I had to push the drawers past their natural stop for the static friction mechanism to hold the drawers from opening on their own.

Since then it has been fine. The casters that come with this box are terrible hard plastic. I switched them out for better casters after the first week of pushing this cart around at work. I just noticed this morning that the wooden top is cracked.

I work in a climate controlled atmosphere and was very disappointed to see this crack. I will be contacting Home Depot to see what can be done about this issue. The metal thickness of this tool chest is very thin compared to different rolling tool chests that I’ve had or seen.

I guess that’s why they can put them on sale for less than $300. On a positive note, there is lots of space for your tools. Especially when you go from a box that’s 28×18.

I really like the workbench so far. I read a lot of reviews that complained about damaged parts – mine came out of the box perfect. While it took me some time to set it up, and moving the butcher block top is better with two people, it looks great.

It really was simple to do, and I’m not that handy. Considered the built in drawer unit, but decided to go with the standalone tool cabinet on wheels for maximum options. Was concerned it wouldn’t fit underneath, and I read differing opinions on whether it would (even from Craftsman) I’m happy to report it does fit well.

(37. 5 inch tool chest height. ) The only thing is this bench is really tall. I’ve never had one this tall, and it takes some adjusting. The grandkids will have trouble with the height, so I will need to get a stool or two.

The workbench assembled easily. The quality is excellent. Picking it up from Farm & Fleet was very easy and straightforward. You do need to be mindful of the overall weight, which is easy if you have someone to help lift the finished unit; but a little more tricky if you are working solo.

I put four locking casters on mine, to make it easy to move around in my workshop, which will be necessary from time-to-time. The caster stems screw right in where the levelers would go otherwise. Trouble-free.

This thing is not HEAVY DUTY as advertised and certainly not worth $250 to $280. It is made of the cheap thin metal that will bends n dent easy. The bolts n nuts used are the CHEAP easy to strip metal.

The ONLY thing nice about this bench Period is the butcher style top. its not a heavy duty sturdy made product. I suggest you go look at it in a store before you consider a purchase. IF the drawer assembly had been included with the bench.

Then Maybe it would be worth the selling price but the actual construction of the bench is dissappointng.

Almost a Perfect Printer. The OfficeJet 9015e is replacing one of the best printers I have owned, the Canon MX922. The HP 9015e prints and scans much faster than Canon MX922. I can confirm the following features which made me stick with it despite having to return it to the store today for a replacement unit.

It does auto duplex printing and scanning so I don’t have to manually flip the paper when using this printer which makes scanning bills into searchable PDF docs a breeze. The HP 9015e has a great feature where you can setup a shortcut directly on the printer so you can send your scans to your OneDrive, Google Drive, Dropbox, etc.

, accounts without the need of your computer. You can also scan documents for digital faxes without needing a landline. If you don’t want to participate in the HP Ink program, simply buy your own ink instead of using the subscription ink that comes with the printer because the provided ink will be deactivated when you stop using the HP Ink program.

I signed up for the 700 pages a program for 6 mo. free and they already sent 2 ink refills to ensure I have enough ink at home despite not printing that much. If you don’t print 700 pages, it rolls over to the next month.

I plan to roll it back down to the $. 99 or $4. 99 a mo. level since I don’t print that much (15-100 pgs. mo. ). Just know that HP will deactivate the ink if it detects you are using their subscription ink after cancelling the subscription so have your own ink if you still want to print.

The Printer sounds like it will break at any moment, and I guess it did because I took it back when scanning to OneDrive produced an error message only when scanning from the Printer after it comes out of sleep mode.

It worked after I cleared the error message but didn’t have that problem when using the same shortcut from my laptop or phone. While I can’t print directly to DVDs like the MX922 or place regular paper and 4×6 photo paper in the printer at the same time, the easy of printing directly from my iPhone/Android devices, laptops, and scanning directly from the printer to cloud or networked storage devices makes this almost a perfect printer.

Hope the printer works out, and yes, I contacted HP same day tech support twice which was nice since they have 7 day a week support using chat or phone support.

The printer has been good so far, though on rare occasion it seems to slip trying to grab a sheet of paper. But that has only happened twice right at the beginning and since then it has not been an issue.

The bigger issue is that HP does not tell you that in order to use all of the features you paid for, you need to connect your computer to their servers with an HP account. That means that every single time you print, you are sending analytic data to HP for their marketing department to use.

If they offered a discount for ink, or a rebate, or even just some money for that, then I would say that was fine. You could make a choice how much this invasion of your privacy is worth to you. But in this case, you really do not have an option.

If you want to use a few of the basic functions of your printer (like scanning) you HAVE to create an account and you HAVE to connect to it to scan. This is called “HP Smart” and it is not optional. I am extremely annoyed by this REQUIRED invasion of my privacy.

I was able to find a workaround by using the built in features of MacOS to scan and print – but I lose out on some of the more advanced features the HP software provides. And none of this is advertised when you purchase the printer.

They sell you on all the cool features, but don’t easily disclose that you have to connect to their servers for every print or scan to take advantage of these features. I am keeping the printer because it is too big of a hassle to return and I found a workaround for basic scanning and printing built in to my OS.

But I will never buy another HP product and cannot recommend this printer to anyone else.

I returned the HP 9015e printer immediately as it did not come close to fitting my needs. It is my opinion the whole HP+ line of printers is garbage mainly because of their software. First of all, I am a long time HP Printer user and have liked them previously.

My current HP printer broke after 12 years so I didn’t think twice to go pickup a new HP printer. I was wrong in thinking things would be the same, after all it is just a printer, right!? 1. Quality is nowhere near my decades old printer.

Plastics aren’t as good, seams don’t align as nicely and ink cartridges do not slide in easily nor do they provide positive feed-back that they are even seated correctly. The paper tray and paper catcher just seemed clunky and cheap to me as well.

2. Setup is a joke. The setup assistant can’t add printers to a different WIFI SSID then from computer running the setup. Ever hear of having printers and computers on separate networks? So you have to add it manually from the printer itself and the keyboard layout is most silly thing I have seen and has no QWERTY layout.

Once you tackle that the 6 months free ink is a joke as well because it is dependent on entering your credit card and signing up for some subscription service (which you can cancel at anytime) so they can start charging you after 6 months is up.

3. The printer does not like name changes or changing to static IP. I had to factory reset and start over because it messes up registration with HP and their Smart App. 4. Printer REQUIRES internet so you can print.

If you need to print from outside your home, sure, maybe you need this feature. Or maybe you have VPN and can connect privately that way. Or maybe you just want to print to your own printer in your private home on your private network, nope, you still need internet access.

Of course, HP will say, just use usb cable or WIFI Direct feature which are silly responses. There is NO need for REQUIRING internet access to print. The only purpose this services is so HP can monitor your usage and sell your data.

Or they’ll say they need to monitor ink levels. Again silly, my 12 year old HP printer told me when ink was low just fine without needing an internet connection. 5. The only thing they did right, was the plastic bag the printer comes in.

It has handles built-in so you can easily lift the printer out of the box. In short, loved the plastic bag it came in, everything else is garbage. I went with a different brand entirely and couldn’t be happier.

It didn’t have the cool plastic bag but all the other issues where a non-issue.

I love this workbench. Weighs a ton! But that just makes it very solid to work on. It’s really attractive in addition to being perfect for my stained glass studio. I use it every day and highly recommend it.

Fantastic workbench we are using it for an outdoor kitchen countertop. Love the look of it and it’s very solid once assembled. Assembly was straightforward and not too tricky. Very pleased with our purchase.

Fabulous work bench! Very sturdy and holds all my tools just fine. It was a beast to assemble by myself, but I got it done. Might buy another one!

Carbonless Colored Sales Forms Booked.This was perfect! Great pricing and arrived quickly! Thanks for the awesome service. We will definitely use this company again.

Carbonless Colored Sales Forms Booked.We were very pleased with our Sales Forms. The forms were exactly as requested. We do recommend this company and will use as well in the future.

These inspection reports are a lot more detailed than what we had been using. Gives our drivers a better perspective of what they need to focus on.

My only suggestion would be to remove the starting odometer. FMCSA does not require the starting odometer and this has caused confusion in the field.

These are a great way to keep post trip and pre trip inspections separated.

I searched long and hard for a good table for my crafting/sewing room. I kept seeing people using the Husky workbenches and I loved the idea of them but they were more expensive and were hard to come by.

I though I was settling for these but it turns out I am in love with them. I have two, one that is at the tallest height that I stand at and the other at the lowest that I sit at. They are heavy duty but in my room they don’t look like something that should be in a garage.

They look really nice. The top is solid wood, heavy as can be, but solid. The base is perfect, I can adjust the height if I need and then legs/frame are set up that I am able to put stuff under them.

They were exactly what I needed and fit my space perfectly. I’m thinking about getting one as a desk for my home office.

Purchased in store and assembled by my wife and I in less than an hour. Packaging was efficient with each piece and all hardware clearly marked. Instructions were very thorough and easy to understand and follow.

Extra hardware is included along with a wrench. I did use a power ratchet for ease of assembly but the wrench would have worked just fine. All pieces fit together with very little drama. Great work bench for the $$.

There was absolutely nothing difficult about the assembly.

Bought this as an “extra” workbench for my new large “man cave” sized 4 car garage. The box it came packed in was very heavy (~90 lbs), so once I got it positioned in the are of my garage that I want to use it for projects, I slir the box open and used the cardboard as a cushion to keep the hardwood bench top from getting scratched up.

It was SUPER easy to assemble and only took about 15 minutes total. Instructions were well written with excellent diagrams. You assemble it upside down (legs pointing to the ceiling), but I was able to lift and position it right side up all by myself and I’m a 60 year old man.

I was very impressed with the heavy duty quality of this work bench. I plan to mount a large bench vise and a small drill press to it. The price was unbelievably good for such a high quality product.

I ordered two pairs of pants because my two year old pants were breaking. I was surprised how long I got out of use of my old pairs. So if course I went with the same company. I ordered with the idea it would take seven days.

It only took three days for delivery. That was my first mind blown. The first day of wearing my mind was blown on how well they held up. I work in housekeeping at a hospital. There is alot of bending to check for nasty stuff in rooms.

Last mind blown ended at laundry mat. I wash them and was shocked on how well they bounce back with little wrinkles. I would recommend them to any new coworker. I rate them four out of five because after wash the button came lose some.

Which scare me but nothing a sewing kit can fix. Totally worth the investment.

These pants are awesome! I love the way they fit. You may have to order 1 size bigger. I normally wear 38 waist. I ordered the 0’s because I’m a growing boy. 🙂 I like the way the cargo pockets expand.

With button snaps, they keep stuff inside. I’ve been trying to find the shorts on the website. I’d like to order a couple pairs of those too.

As a HVAC contractor I like pockets and want to look professional. These pants fit good and look good. (I hate big boot cut pants). The price was reasonable and they are thicker than others that I have.

That being said they will be nicer for the fall and winter, not so much my choice for middle summer in the attic. I absolutely love that there is in between average sizes. (33W33L) The waist is a little snug but I haven’t been wearing them for a too long yet, so they may stretch or relax.

The length is good though. Great paints overall.

Carbon Copy Auto Repair Order Forms.Good product at a reasonable price. Not the highest quality form I have purchased, but for the price it is well worth the money.