Cleaning products for mold can include a variety of different chemicals and solutions. Some common cleaning products for mold include bleach, vinegar, borax, and hydrogen peroxide. When choosing a cleaning product for mold, it is important to select one that is specifically designed for mold removal.
Many household cleaners will not be effective at removing mold. In some cases, mold can be removed with a simple soap and water solution. However, if the mold is more deeply rooted, it may require a more powerful cleaning solution.
20 Best Cleaning Products For Mold
1. RMR-141 RTU Mold Killer, Disinfectant and Cleaner (32 oz)
It is effective against a broad spectrum of bacteria, is fungicidal, and inhibits odors when used as directed. It delivers non-acid cleaning performance in an economical ready-to-use bottle. When used as directed, RMR-141 RTU will disinfect, clean and deodorize most residential and commercial surfaces like; kitchens, bathrooms, hotels, offices, hospitals, basements, behind and under sinks and countertops, garbage cans and storage areas, and other places where bacterial growth can cause malodors.
RMR-141 RTU is an all-in-one product for treating wood framing, carpets, and other porous and nonporous surfaces as well as part of a complete mold remediation project. This is your go-to product for water damage restoration, sewer cleanup, mold removal, disinfecting porous surfaces and deodorizing.
Its the only ready-to-use disinfectant that kills 141 organisms!.
I always thought this was more of a mold killer and disinfectent until i recently used iit on the kitchen floor right out of a spray bottle. I soaked the floor in sections about 4ft by 4ft then brushed it around because our floor is not smooth it has some texture to it and Im not good at always taking my work boots off everytime I run in from outside to use the bathroom were as my wife reminds me so i figure lm going to disinfect the floor but to my surprise the RMR sprayed ,scrubbed a little then wiped up with a big old bath towel flipping it around as to keep a clean section to the floor done a super job at removing my ground in dirt disinfecting and the floor was not slippery as with some cleaners i have used in the past when it dryed.
I was impressed. Oh I should mention so was my wife.
spent a boat load of money on this and Rmr 86. at first I was really impressed. Seemed to work as advertised. under 10 to 20 seconds. stain gone. wood literally looked brand new. i WAS really happy. I then applied the RMR 141 RTU.
AS DIRECTED ON LABEL. after this. no lie. all the wood looked brand new. Extremely impressive. BUT. I returned to my attic exactly 2 and a half weeks later. only to find probably 75 or more percent of ALL the stains were RETURNING.
Very disappointed. especially after spending over 500. 00 on all this “Miracle” solution. Not worth the EXPENSIVE PRICE TAG IM SORRY. I literally went to the biggest grocery store you know. bought 7 or 8 gallon jugs of CLEANING BLEACH.
returned to my attic and applied bleach straight to the areas of returning mold. Yea it took about 1min for the stain to disappear. but. months later. NO STAIN OR MOLD GROWTH. I’d ask this company to refund my money if I hadn’t used it all.
Hands down bleach was the better option. LOADS CHEAPER AND MOLD STILL HASNT RETURNED. over 3 months now and STILL NO MOLD GROWTH. Maybe I’m just lucky. but after applying bleach to the same areas that , after using RMR SOLUTIONS(AND IT RETURNED NOT EVEN 3 WEEKS LATER).
there is no new mold growth. Save a few hundred dollars. go with bleach. This product did remove it fast. but what does that matter if it returns in less than a month?.
Concrobium Mold Stain Eraser is a powerful cleaning solution that targets tough and embedded mold and mildew stains on outdoor and indoor surfaces. Perfect for black mold stains. Ideal for: Tile showers, bathrooms, basements and outdoor furniture, decks, patios, fences, walkways, railings, siding, gutter and roofs.
Works on: Wood, composite wood, concrete, masonry, drywall, grout, stone, fiberglass, tile, plastic, laminate, aluminum and metal.
I have been searching for over a year for a mould remover. I was about to give up when I found Concrobium Mould Control. Bought it to clean the mould from the seats on my 12 year old pontoon. I tried it on the captains chair with poor results.
Then I realized from reading the internet literature again that what I really needed was Concrobium Mould Stain Eraser. Went to Lowes and bought a jug. My wife chastised me for wasting my money on another useless product.
I mixed up a 1/4 supply as per the instructions and tried the captains chair as a trial area. Came back 2 hours later to find I had one clean chair and a bunch of very dirty seats. Early the next morning while the boat was still in the shade I mixed up another 1/4 supply and Started on the seats.
Two hours later my wife came down and was completely shocked. The seats look brand new, it is absolutely unbelievable. I went over to my son’s place ( he has a brand new boat, sold his old one because of mould stains).
I told him I had just replaced my seats on the boat, what did he think? His response was how much did they cost you? When I told him $20 and 2 hours of work he was floored. No one can believe how good the seats look.
The boat feels and looks brand new. Thank you CONCROBIUM. Wish I had taken before and after photos.
Super-great product. The only one I’ve found that can get rid of 1-2 yr. old mold stains of Sunbrella covers & biminis & furnature. It’s somewhat “involved”, & a bit of work. (I’ll be making a video) But worth the work.
They’ve stopped making it (hopefully they’ll change their minds on that bad decision), so it’s wuite expensive at “scalpers” rates.
Just opened up our nice hardtop and found dome mould on an bulk end. Really not happy. I am pretty anil so I reasearched lots, then went to my neighbourhood Lowes. Asked my contact and he recommended this.
Got home, measured out what I needed added HOT water, waited as per instructions and applied with a clothe. I wore gloves and eye wear just because. 90 percent came off right away. Amazing. Will spot dab 1 area.
Highly recommend. Ps, and it’s safe for my Rockwood Premier 2317g canvas.
New and improved sprayer works in 10 minutes guaranteed Removes mold and mildew stains Reaches 2nd story Cleans wood, vinyl and brick siding Cleans up to 4,500 square feet Home Armor E-Z House Wash Hose End is like pressure cleaning with your garden hose! With the new easy spray selector, Home Armor E-Z House Wash Hose End quickly and easily removes dirt and exterior stains caused by mildew, mold and algae from the exterior of your house.
All without any scrubbing! The new and improved spray nozzle has four options to meet your cleaning needs. Jet setting, shower setting and two options for wide spraying. The 64 oz. bottle cleans up to 4,500 square feet and easily reaches your second story.
With its patented design, Home Armor E-Z House Wash Hose End is 2X stronger than competitive hose end products that deliver bleach-based formula. Just spray it on, wait 5-10 minutes, then rinse it off.
Cleaning your siding is that easy. It’s guaranteed to work in just 10 minutes and is ideal for use on: vinyl, brick, painted wood, stucco, concrete, trim and siding.
I tried three different hoses and all three popped off of the cheap plastic piece that the hose screws into. I even tried to have the unit in the open position (in hopes that this would create less pressure) — no go.
Every time I turned the hose on, it popped off of the item. I even resorted to using plumber’s tape in hopes that this would create a better seal. Nope, this time, it didn’t completely pop off, but more water squirted backwards than went thru the item.
Obviously, I have no idea how good the product works because the manufacturer saved a nickel by using a cheapo plastic adapter for the hose to screw into.
Well not sure what the result should be but it didn’t make a difference for me. I still had to get very close with my pressure washer to remove the dirt off the siding of my home. This did nothing but make it smell like a chemical and create suds.
Just plain water worked much better and it was the force of the pressure washer that removed the dirt and mildew, not the liquid chemical. Now if the purpose of using this is to create a coating on the siding to prevent future build up then we will have to see, but it did absolutely nothing to clean it.
I even sprayed off some of my brick patio to see if it would kill some of the moss and grass growing, waited 48 hours to see if the chemicals would kill it off, and it did nothing. I would suggest grabbing a ladder and using soap and a sponge on your home, then rinsing with the pressure washer.
I would also recommend using a grass and weed killer on your patio, and again just using the pressure washer to rinse. These two methods have worked for me, and I guess I was hoping to avoid the extra work it takes by using a $10 cleaner.
Haha right, I did know ahead of time it seemed unrealistic but I trusted the reviews enough to try it anyway. That is why I wrote this, so you can save time, money, and the embarrassment of fooling yourself.
WOW!! I would highly recommend. I had serious mold on my travertine stone pavers on my walkway to my front door. I used chlorox, pressure cleaned – nothing. Then, I took a chance on this item and it just cuts right through it.
I made a mistake by using an old Hudson sprayer that did not spray, just dribbled. I wasted a lot of the product. Make sure you have a good sprayer and do not water it down.
Home Armor, 32 oz. , instant mildew stain remover, twice as strong as the leading brand, bleach based formula, cleans mold & mildew stains Adds extra shine to your product Removes mold and mildew stains and odors caused by mold Cleans with no scrubbing Cleans with the power of bleach Is twice as strong as the leading product Ideal for use on tile, grout, tubs, toilets, fiberglass, shower doors, vinyl curtains, counters, and sinks.
The first thing to note is this is a lot stronger than I expected both in effectiveness and smell. DEFINITELY use in a well-ventilated area or it can take several hours for the fumes to go away depending on how much you use and how well you rinse.
You also definitely want to wear gloves while you’re using to avoid skin irritation. Also if you have any respiratory issues or you are sensitive to strong smells you may want to wear a mask (the smell is vaguely similar to bleach if that helps at all).
My house has varying levels of impact from mold all around the house and I found a very bad/thick area of mold yesterday which pushed me to do more about it than spot clean (which is why I bought mold armor).
I was disappointed this morning when I checked that area and there was still mold BUT the bottle does instruct you to pre-clean highly affected areas so that it can penetrate better, which I didn’t do.
I sprayed it again a few minutes ago and it’s already looking better. Another thing to note is that it is also a mold stain remover. This means it can “bleach” fabrics or other porous materials. I did have this happen on the side of a wooden table, but I noticed it and wiped it off quickly, and its not in a noticeable spot so I don’t really mind.
If you’re using it in a highly visible spot though, I would recommend spraying it on a rag and then wiping it around until dry (and then rinsing). It may not have the same preventative effectiveness as letting it sit for ten minutes but it will still get the mold off.
Overall it seems to be very effective in killing mold; the mold began to dissipate immediately upon being sprayed. I can’t speak to the preventative effectiveness of it since I’ve only been using it for about 12 hours.
The instructions do say to reapply every seven days to inhibit mold growth, which is the biggest downside to me since my house is hard to ventilate and the chemical is so strong. TL;DR it seems to be a great cleaner both for mold and otherwise, but read instructions to use it safely and effectively.
I had some stubborn mold in the shower stall in a bathroom that has no windows, so it is so often damp and dark, a perfect place for mold! I have used other bleach products which work fairly well, except the mold eventually returns.
The products I have been using require laborious application and then scrubbing with a brush. This MOLD ARMOR spray is amazing! I used it on the few areas that did not respond to my usual remedy and within a few minutes the grout was beautifully white again!! The odor is pretty rough, so do use a mask, rubber gloves and I recommend goggles.
I ran the vent fan, also. I just rinsed the shower after about 10 minutes and I am very happy!! Who doesn’t like an effective product that does not require a lot of scrubbing and toil? Hurrah!! I do wish that the product had more specific instructions about how long to leave on, and if it can go on wet surfaces or needs to be on dry surfaces.
I had a small hint of mold in the corner of one tile in my bathroom, so I decided to use the product to kill and seal the place. After I sprayed and nothing happened, in few hours all tile grout that was sprayed over started to get yellowish.
in few more hours orange, and at the end of the day it was all dark brown. on a completely white tile grout before. I tried to clean it with few products, including bleach. No results!!! It stays dark brown as it was some kind of resin that sogged in the grout.
Thank you, Home armor, for I have to regroit my bathroom because of your awful product!!! I’m so frustrated that one product vas do such damage. I wish they allowed me to post some pictures to show you.
Clean up the outside of your home fast with Mold Armor E-Z House Wash. This exterior house cleaner blasts away dirt mold and algae stains leaving your siding looking bright and new in minutes – no ladder or scrubbing required.
Powerful cleaning action kills mold and mildew down to the roots. Microban foaming technology lifts away dirt and debris and clings to surfaces for a long-lasting clean. Safe for use on vinyl brick stucco aluminum concrete and more.
Use formula at full strength for tough stains or dilute with 3 parts water 1 part formula for typical stains and dirt. Directions for use: Spray surrounding plants with water. Apply with a garden sprayer roller or sponge.
Apply full strength with a garden sprayer. Do not use a high-power pressure washer. Wait 10 minutes. Rinse well with water. If stains persist a second application may be necessary. Rinse surrounding plants with water.
Wear eye protection and rubber gloves during use. Keep out of reach of children.
We just bought a brick house and need to clean the brick. We got this to try if the weather ever cooperates. It’s been cold and windy which are two things that aren’t a good idea with trying to clean.
I have read to make sure to wear eye protection when using this. This product BLEACH in it so be aware of that also and don’t wear anything that could be ruined. We tried a small test on our concrete driveway and it seems to work.
I also read that you might need multiple applications and with our house that will probably be the case. I think overall this product does what it needs to after we tested a small part. We will see how the rest of the house is once we really use this.
Mildew Stain Remover quickly removes unsightly mildew stains from fiberglass, vinyl, plastic or painted surfaces. It begins working on contact. The special buffered formula will not harm vinyl upholstery or threads.
It is a much safer alternative to using bleach and can also be used around the home or in RVs wherever mildew stains are a problem. Directions: Just spray or wipe Mildew Stain Remover on boat tops, vinyl cushions, vinyl chairs, vinyl canopies, tile, grout, shower stalls and curtains, mats, awnings, etc.
Do not rinse until mildew stain disappears. Stubborn stains may require a second application and light scrubbing. Rinse well after use. Not recommended for use on fabric; test for colorfastness in an inconspicuous area before proceeding with overall cleaning.
This stiff just ate away all the black mold on our canvass Awning. D Still a few spots, but wish I had taken a proper before/after pic! I caught a picture of one side that was only half way done working its magic, and the other side which was mostly done.
If you could have seen this thing before i sprayed it you probably wouldnt believe me. No scrubbing involved. Pricey but quality product.
Kills, eliminates, and prevents mold No ammonia or vocs Can be used on all surfaces interior and exterior Concrobium mold control effectively eliminates existing mold, prevents mold re-growth and eliminates musty odors with no harmful chemicals.
Ideal for homes, buildings, boats and cars. Works on drywall, wood, composite wood, plastic, concrete, shakes, metal, brick, stone, tile, grout, fabric, furniture and many more surfaces. Invisible shield prevents new mold growth.
The unique technology is used by homeowners, professional remodelers, contractors and remediates. Concrobium works as it dries by crushing the mold spores at the roots and leaving behind an invisible antimicrobial barrier to prevent future mold growth.
Apply Concrobium Mold Control in a thin, even layer over the affected surface. Allow to dry completely. with a Concrobium dampened cloth or brush, scrub the surface to clean away any remaining mold stains and residue.
To protect against future mold growth, reapply Concrobium mold control on vulnerable surfaces. No bleach, ammonia or volatile organic compounds. Comes in 32-ounce trigger spray which covers up to 100-square feet.
People are not using this product correctly. To remove mold stains use bleach or high strength peroxide. After the stain is gone, use mold control in the same area to prevent mold returning. Bleach does not kill the roots of mold, but it does remove the discoloration.
The mold control product has successfully kept mold at bay in my house. Only failures I have had are with fabrics, Insulation around air ducts.
I paired this with Mold Armor and it obliterated the mold I had on the studs in my bathroom. I emptied the bottles on all of it approx 5’x8′ space. Made sure to apply at least 2 coats(3 on the heavy stuff).
I scraped the mold off with a paint scraper and steel wool. Wiped off with blue shop towels, dried, and then sprayed again. 24 hours later the wood is mold free and I can start painting it over with Kilz.
An ok stop gap, but this is no substitute for professional mold remediation. I sprayed this on mold in my closets to prevent it from spreading on the surface of my walls until professionals were able to remove the carpet, pad, trim, drywall, insulation, and tack strips.
It seemed to stop the visible mold, but I would never use just a spray on moldy build materials that should be removed in spite of the product’s advertising.
Remove stubborn mold and stains without scrubbing or using bleach with Wet & Forget (800006). It’s easy to use. No rinsing, scrubbing or power washing is required. Simply mix with water and apply it with a pump-up garden spray.
The Wet & Forget mold remover goes to work to gently remove growths over time. Surfaces stay clean for up to one year or more in most cases. Wet & Forget outdoor cleaner is a gentle formula so it can be used on non-porous outdoor surfaces like siding, roofs, decks, walkways, painted surfaces, vinyl, plastic and fabric patio umbrellas.
Available in a single, one-gallon container, it also comes as a convenient two-pack to meet the needs of larger surfaces. Get the job done with this non-acidic concentrated cleaner.
First off, I ordered 2 jugs, and after I got it opened and started reading the instructions, you’re supposed to apply it on dry surfaces. Mine were damp, but I didn’t think that would be a problem. Both jugs were supposed to have a 3′ little tube/hose to attach the sprayer to one end and stick the other into the top of the jug.
No tube on either jug. I had to jam the sprayer into the top. I doused everything and then read on the back that for green stains it can take 3-4 DAYS, and for dark or black stains it can take 2-4 weeks or longer for them to fade.
I could have just squirted some soap on them and hosed it down if I didn’t want it to look like I just cleaned. That is far too long for results, it cost 2x more than 30 seconds cleaner , and cleaned about the same, which in my view didn’t even make a dent.
Don’t waste your money. After it dried there was a sticky film on everything as well, which there is no way I’m waiting a month or more to see if it fades. I don’t recommend this product.
I’ve applied this product using an inexpensive garden sprayer with a hand pump which made on gallon at a time. I brought the garden hose end up to the roof so I I could refill it as I went along, making a new mixture each time.
Because it will cause foaming, I slowly added water first, then the Wet&Forget concentrate to avoid foaming. Two weeks ago, I applied another dose because the shingles had a good amount of black mold.
When applying, try to do a few rows of shingle at a time to make sure you get a more even covering. I went up on roof two days ago, and it looks like the mold is slowly fading. We haven’t had much rain since the earlier applications, so I’m not expecting a rapid remediation.
My neighbor also noticed the change. For an average size home, the two pack should be enough for one application. If you have any left over, just make more mix and hit the darkest mold spots again to heavier coverage.
The best time to apply is in late afternoon when sun is low and shingles are not hot, to give the solution time to wet the shingle surface and better personal comfort from too hot a sunshine. Also, since shingles remain wet longer, you can more easily see where you sprayed to better insure uniform coverage.
Hopefully, the mold will be fully gone in a few more months. Then, I’ll be sure to reapply again in a year or two to keep more mold from forming.
Have used this product on my driveway, patio and sidewalk for several years. The first time I used it the concrete surfaces were either black or varying shades of gray. I did two treatments per the label instructions and in about 6 months I could see a difference.
After approximately 9 months all of the treated surfaces were looking as new. I now apply the product every year and the concrete continues to look new without any mold. I still do two treatments each year but I probably don’t have to.
The manufacturer claims it will not hurt lawns and I can attest that it had not damaged any of my landscaping. Wet & Forget works well for me and Sam’s sells it for the most reasonable price.
This stain remover removes mold mildew stains and odors caused by mold. Its powerful formula is twice as strong as the leading product and allows you to clean with no scrubbing. It is ideal for use on grout, tubs, tile, toilets, fiberglass, shower doors, vinyl curtains, counters, sinks more.
Bleach based formula. Disinfects odor causing germs Use indoors outdoors. Twice as strong as the leading product. Cleans with no scrubbing Use on both interior and exterior.
10/10 this stuff is freaking great. I feel like you could put it on a moldy piece of bread and it would make it new. Jk. But put it in a couple closets that were ate up with mold so bad it was getting on the stuff in there.
Threw everything away, sprayed it all over the walls and then wiped it with a dry rag after a couple minutes and they looked brand new. Temporary fix to a bigger problem in my case, but it for sure works.
Blew our minds when we came back and all the mold was gone.
JOMAX is easy: Mix with bleach and water, spray on, rinse off. No scrubbing or power wash equipment needed! JOMAX is economical: One gallon of JOMAX makes twenty gallons of solution – a fraction of the cost of pre-mix cleaners.
JOMAX is effective: The patented JOMAX formula kills mold and mildew on contact, while removing dirt and stains, yet will not damage glass, aluminum or painted surfaces. – Use JOMAX for routine cleaning or for prepainted mildew control.
Kills mildew on exterior non-porous surfaces such as: aluminum and vinyl siding and stucco; painted wood, doors and trim; painted brick, concrete or cement block; stained or painted decks and fences; and patio furniture.
I have been using Jomax for many years. It is one of the only products that you can blend with bleach. I make the mixture per the directions on the side and use a garden sprayer to apply it to what ever I am cleaning.
I use pressurized water (not a pressure washer) to wash the dirt, mold and stains off after letting the blend stay on the surfaces. Rarely do I have to use a brush. Maybe another light application of the mixture if an area was real bad.
I have used it on brick, metal, vinyl siding, wood siding, patio furniture, decks and concrete. Very happy customer!.
This stuff worked great. I tried another brand a month ago and it barely did anything. Jomax did an amazing job. I followed directions carefully, measured and applied carefully. 15 minutes later my severely discolored vinyl was sparkling clean.
My house had plenty of dirt and mildew built up on the vinyl siding. I’ve used other products that had great promises – they didn’t live up. Jomax actually lived up to it’s promise. Worked like a charm.
I’m guessing the only way someone would be disappointed is if they did not follow the directions. Mixed it as directed and sprayed it on with a good garden sprayer – wet it good. I watched the dirt and mildew disappear even before I pressure washed it.
Mold Armor Mold Remover and Disinfectant is a one-step formula that kills 99. 9% of household bacteria and viruses, destroys odors and inhibits the growth of mold and mildew when used as directed. This EPA registered formula is an effective way to clean up after storms, floods and sewer backup.
It is also effective against odor caused by smoke. For household and institutional uses. A One-Step Disinfectant, Cleaner, Sanitizer, Fungicide, Mildewstat and Virucide.
This product works as designed. Educate yourself on the various products and how they work before purchasing. i chose this product since it was highly concentrated. i am currently remediating mold and this product will go a long way.
i will use it in various areas, but my current intended purpose is to spray the dirt in my crawlspace before encapsulating. Lets get something clear first. There are products that kill mold and leave the body behind and this is absolutely fine.
it all depends on the intended purpose. if you intended this product to kill mold and remove the body with absolutely no work on your part, then look elsewhere. Bleach will obviously make a noticeable difference vs this product because bleach “bleaches” and can dmg the surface you are working on.
furthermore , bleach is not preferred because it stays on the surface of what you spray. if you intend to use bleach, then mix with dish liquid to help it soak into the surface. bleach is not approved for mold remediation but it does have uses so take the time to research what you really want and which products will give it to you.
do you want to kill everything? do you want to kill it and remove it with no work? there are products many times more expensive , but this product is cost effective and worth it.
My mother has a bathroom where even though she has an exhaust fan, the moisture still has a tendency of being a little much at times. She noticed a little mold on her wall. She used this and it made things easy for her.
She followed the instructions on the bottle and went to work. The smell of this cleaner isn’t overbearing. It’s got a pleasant scent and doesn’t smell super chemically. She didn’t have to scrub or anything.
It just wiped off. It also didn’t take any of the paint of the wall like some cleaners she has used in the past. The thing that we have noticed after using this is that it does help with her not accumulating mold as quickly.
We will he replacing her exhaust fan with something a lot better this weekend but we will definitely always keep this on hand if we ever run across the issue again.
MOLD ARMOR E-Z House Wash is an easy outdoor cleaning solution that kills mold and mildew in minutes. It cleans the toughest outdoor stains with its bleach-based formula, blasting away stains caused by algae, dirt, and debris.
E-Z House Wash will not harm your plants when used as directed. Great for use as a siding cleaner, vinyl, brick, stucco, aluminum, concrete, painted wood, trim, PVC, plastic, masonry, and gutters. To use as mold remover or mildew remover, spray surrounding plants with water before and after use.
Start from the bottom and work upward. Wait 5-10 minutes before rinsing. To use as vinyl siding cleaner surface preparation, use formula at full strength for tough stains or dilute for typical stains and dirt.
Apply with a garden sprayer, roller, or sponge. Do not use a high-power wash pressure cleaner to apply. Wait 10 minutes and then rinse with water. This is a 1-gallon mold cleaner refill for an E-Z House Wash Hose-End product.
Keep out of reach of children and follow all directions.
My father in laws house has light brown siding and every single spring we have to get buckets and sponges and soap and scrub his siding down because it gets that nasty mold and mildew on it. My husband found this mold armour EZ house wash and it works So great! It’s so easy to use.
No more buckets and scrubbing! You simply hook the bottle up to a garden hose and start at the bottom of the siding spray and coat the siding all the way to the top. Wait 10 minutes and rinse. A few of the thicker mold/mildew we had to do again but it’s so simple and easy.
Controlling mold and mildew is important not only for maintaining appearances, but also for creating a healthy environment. Spray Nine Mold & Mildew Stain Remover is the ideal cleaning product for accomplishing both.
With regular use, Mold & Mildew Stain Remover will prevent growth of mold on treated surfaces for 7 days. It also disinfecting hard non-porous surfaces in only 45 seconds versus the 10 minutes typical of most competitors.
We own a camper and this is all I use to clean the outside of it. Our camper gets black streaks running down it after each rain or just sitting. if you own a camper-you know about the black streaks that always come.
This product works so perfect to wipe those off. I tried other products and did not work as good as this. It is easy to use, spray on and wipe off. It a spot is harder to get off I just let spray sit on it for about 5 seconds then wipe.
Our camper has been painted 3 years ago. This product does not harm our paint. As long as we own a camper, I will always have this on hand. It really works perfectly. The smell isn’t overpowering either.
Mold and mildew stain remover size 32 ounces Tough on stains from mold and mildew without using bleach or other harsh chemicals. This bleach-free formula dissolves stains from mold and mildew and forms an invisible shield that protects against stains in the future.
1. Always test on an inconspicuous area. 2. Turn nozzle to spray position; spray 6-8 inches from the surface and allow to sit 5 minutes. 3. Rinse or wipe clean with a wet cloth or sponge and allow the surface to dry. 4. For tougher strains, scrubbing or an additional application may be required. 5. Re-apply product lightly without scrubbing or rinsing to help protect the surface. 6. Repeat every 1-2 months.
Caution: Eye and skin irritant. See other cautions on back panel. Contains Ethoxylated alcohols. Avoid contact with eye and skin. First Aid: In case of contact with eyes or skin, flush with water for 15 minutes. If irritation persists, seek medical attention. If swallowed, take large amounts of water. Do not induce vomiting. Get medical attention. Safety Data Sheet available. Keep out of reach of children. For emergency, call your physician, local poison control center or local emergency room. For product health information, call: 847-367-7700.
Reviews From Real Customers
This stuff worked great. I used it on some mold around my windows and patio doors that have been there for over a year and it came off no problem. I let it soak for about 5 mins as outlined in the instructions.
Tried using vinegar in the past on mold in the same areas and it didn’t work very well. Highly recommended.
I had some very dirty spots with black mildew on the back of the house and a few sprays of this and a bit of light scrubbing has it looking better than new. Love that it doesn’t have any bleach in it yet still cleans so well!!.
Our grandparents, uncles, and aunt’s gravestones were barely readable due to the buildup of the moss that grows on them. We didn’t know if the mold and mildew remover would work but it worked wonderfully.
First we sprayed them, let them soak and used a soft brush to remove the moss, rinsed them and they looked like brand new even though one was over fifty years old. Highly recommend this product.
JOMAX Mold & Mildew Stain Remover cleans and removes mold & mildew stains from walls, ceilings and wood surfaces so they are clean and ready for painting. The bleach-powered formula is great for cleaning and removing mold & mildew stains on fiberglass, tile, grout, vinyl, plastic and other surfaces in mold & mildew-prone areas like bathrooms, basements, laundry rooms and kitchens.
And, it also removes tough soap scum buildup. JOMAX Mold & Mildew Stain Remover is easy to usejust spray on, wait five to ten minutes for stains to disappear and rinse off! No scrubbing is required. Available in a convenient 32 oz.
spray bottle, the adjustable spray head delivers a spray or a stream of cleaner. When used weekly around sinks, bath and shower stalls JOMAX Mold & Mildew Stain Remover can prevent mold, mildew and soap scum buildup.
My neighbors don’t particularly care for the bleach smell when I use this, but when it comes to getting rid of the black mold spots on my composite decking or the green mold that forms on the vinyl siding where the sun never hits, nothing beats this stuff.
spray it on, let it sit for 5 or minutes, and spray it away with a hose. No scrubbing needed. No power washing needed. You can’t beat this stuff.
Mold & Mildew Stain Remover Plus Blocker is a no bleach professional strength formula that removes tough mold and mildew stains and protects as it cleans. Safe, fast, and effective on most interior and exterior surfaces.
Cleans and prevents mold and mildew stains, Interior / exterior use, Fresh floral scent.
We, (my husband & I) were fixing a condo across town. The bath tub drain was clogged up. Some really horrible stuff came up when we put the drain cleaner into the drain. I had just bought this product (krud kutter) the day before.
It really cleaned that tub. Then I decided to clean the grout in my own kitchen. I tried several different products. Then I tried the krud kutter. Wow!! I was really happy with the results. I would definitely recommend it.
Get the stain-busting cleaner that will have your bathroom shining like new in no time! This fast-acting formula with bleach makes cleaning easier by attacking mold and mildew at the root to quickly remove stains without scrubbing.
With minimal work for you, you can have your surfaces sparkling in no time. This solution whitens fiberglass, tile, and grout, making it perfect for showers, bathtubs, and tile. A must-have for homes, hospitals, schools, cleaning companies, and more.
Get rid of stubborn stains without all the elbow grease with Zep Mold and Mildew Stain Remover! Available in 28. 8 Units per Case.
Always test in an inconspicuous area prior to use. 1. Spray on the surface. 2. Allow to sit for 2 – 3 minutes. Do not allow to dry. 3. Rinse and repeat if necessary. If product contacts porcelain or metal, rinse immediately.
Eye irritant. May cause irritation to skin and mucous membranes. Contains sodium hypochlorite. Avoid contact with eyes and prolonged contact with skin. Avoid breathing vapors or spray mists. Use only with adequate ventilation. First aid: eyes: flush eyes with plenty of water for at least 15 minutes. Get medical attention immediately. Skin: flush skin with plenty of water. Get medical attention if irritation develops. Inhalation: get to fresh air. If irritation persists, get medical attention. Ingestion: do not induce vomiting. If person is conscious, give plenty of water to drink. Get medical attention. Handling & storage: keep container closed when not in use. Store in a cool, dry, well-ventilated place. Do not reuse empty container. Keep out of reach of children and pets. Do not mix other products or household chemicals, dangerous fumes may result. Keep bottle in upright position. Do not place bottle on clothing, carpeting, upholstery or any surface that may become discolored or damaged. For emergency medical assistance, call your local Poison Control Center or 877-541-2016.
Reviews From Real Customers
The pro is that it totally works! I’ve gone through many, many cleaners to get rid of mold stains on the grout of my small tiles in my 90s shower and nothing worked. scrubbed with the toothbrush, used chemicals, natural stuff, nothing worked.
this works basically on contact and with a toothbrush on grout, it looks like new. Highly recommend wearing a mask while using it and having some kind of ventilation as it has very strong bleach/chemical smell.
The other thing I noticed is after you initially clean it with this it really does a decent job preventing the mold and mildew from building up again.
Really bleaches out mildew. I used it in some rarely-used lockers on my boat that were covered in mildew and the Zep cleaned it right up. Or at least bleached the mildew away, whatever. The lockers looked like new.
I rinsed them out a couple of times to make sure I wasn’t leaving bleach behind to eat away, but all in all, definitely works. Make sure you have good ventilation and wear gloves!.
I had a bathroom shower re-tiled in 2011, 6 years ago. I had it professionally done, so wanted it to last. It was not cheap, and I am. Was advised NEVER TO TOUCH YOUR TILES WITH ANYTHING ABRASIVE! You’ll deglaze your tiles and wreck your grouting.
It’s why Tiling is such a great business to be in. People wreck their tile the second they start scrubbing. How do you clean that part of the shower, with all that grout and grout sealant to worry about! Once ever 2 months, I spray Zep Mold and Mildew stain remover on my shower while it’s still wet from my shower.
We are a family of 5 and that shower gets used constantly. This product not only keeps the tiles clean, stripping off soap, shampoo and conditioner residue, but it seems to settle into the pores of the surfaces, caulk, and grout, making sure mold mildew and scum are never get hold.
Seems to solve things for about 8 weeks, protecting it from getting”grossness” as my son used to call it. Skip the wiping step on the bottle, says my tile guy. Even that’s too dangerous for the grout, and will quickly damage the grout sealant coating.
Couldn’t say enough about this ultra-strength chlorine based cleaner. I’ve used it on the outside of my hanging roof gutters as well, the greyness just melts off with a gentle spray. Only side note, spray and vacate the bathroom with the fan on, let this stuff sit in the wetness, then spray it down or let the next shower naturally remove what’s left.
It’s why community swimming pools deck surfaces never get mildew, the chorine inhibits any growth. Sounds too good to be true, no more squigy, no more using a towel to dry down my beautiful Italian tile.
Get rid of stains left behind by mold and mildew instantly Our fast-acting cleaning spray quickly eliminates stains left behind by all varieties of mold and mildew that are often found growing in wet, damp environments such as shower walls, bathroom tile & grout and windows, shower curtains, kitchen tile & grout, wood decks, vinyl siding and painted surfaces.
Keep your home smelling fresh and clean Unlike most cleaning products on the market, our stain removal spray not only lifts stubborn mold and mildew stains, but it also tackles the roots that may be left behind.
Roots may cause hard to remove smelly and musty odors. Keep the air in your home smelling fresh and clean – no scrubbing, vacuuming, or soapy water necessary! Versatile formula for multiple applications Remove tough stains from your outside patio and deck surfaces, wood and concrete floors in your basement, damp brick walls or pathways, kitchen tiles and other areas where mold and mildew tend to grow at an accelerated rate.
Removes molds of all colors When most people think of mold, they think green and fuzzy or possibly the dark blue-green you see on old loaves of bread. You may have been taught to keep an eye out for ‘black mold’ as this is one of the most dangerous varieties.
But in reality, mold not only comes in a wide variety of colors, it also changes colors over its lifetime. Our stain removal spray lifts stubborn spots left behind by any mold or mildew.
I bought this bottle of mold remover based on good recommendations. Sadly, it quickly turned out to be a disaster. The squirter on the bottle no longer worked: at $20 for a bottle of mold remover you would certainly expect better than that.
Be careful with the bottle since is likely to spill and with all the bleach in it, it will discolor any thing it touches. It also really stinks because of the intense amount of bleach. Nonetheless, I called the company and simply asked for a replacement for their broken squirter on the bottle, but the abrasive woman I spoke with said she would not provide a replacement of the part, stating that the product only lasted 8 months.
So a $20 bottle of mold remover, more than double the competition, Mold Armor, which is also a mold preventative only lasts 8 months. Yes, she said. I said it certainly did not say that on the bottle or in the description.
She said we don’t have to disclose it, but it is on the Website if you look at the fact sheet–as if anyone is going to do that. So you have in insanely overpriced bottle of mold remover that goes bad in 8 months, has a bad squirter, and intentionally tries to hide the fact that it goes bad in an incredibly short period of time, and has awful customer service to boot.
Next time I’ll buy Mold Armor at half the price. Never again with this company!.
so. i was skeptical. okay. very skeptical. At the end of winter i went into my son’s (unused) closet, only to discover, over winter, it was taken over by mold. i took bleach to it amd scrubbed. and scrubbed.
and scrubbed. no such luck. i startled googling ideas and what i could use on it, and then started googling reviews of those products. which led me to purchase this. within SECONDS of spraying. the mild disappeared! it was literally like a magic trick and my boys and i were shocked watching it.
their entire closet was like new within 5min of starting and spraying everything. my ONLY suggestion, use a fan! the closet was enclosed and my eyes and throat definitely startee burning and watering.
i threw a fan in there and closed it off until the smell dissipated. i am recommending this product a million times over and over again!!!!.
Iosso Mold and Mildew Stain Remover is color and fabric safe. It removes mold, mildew, algae stain, bird droppings, spider droppings, tannin (leaf) stain, tree sap, tough dirt, grease and oil, some food and drink stains, blood stains and more.
Recommended for use on awnings, tents, boat covers, canvas, cushions, carpeting, umbrellas, camping gear, inflatables, fabrics, vinyl, plastic and fiberglass. It is non-chlorine, biodegradable and has no harmful vapors.
One 12 ounce jar makes up to three gallons of solution. One gallon cleans 150 square feet. The 65 ounce pail makes 16. 25 Gal. s. The half ounce single use packets are great for camping. Easy to carry and easy to use.
This stuff works great. Just follow directions. Staff were helpful with advice for our particular use of their product. Only downside is the price. It is expensive. We did try a couple of other company’s products first, as recommended by our local RV dealer.
But they didn’t do the job. So the extra cost was worth it.
This is the greatest mildew remover product I have ever used. Spray it on and it seems to melt all of the mildew and mold away. Leaves everything looking like new. Have told all of my friends about it.
I have used Iosso for over 10 years. It wires slowly but realized mold stains that other cleaners don’t. Sometimes I need to use several treatments or leave it in overnight. It always works and does no damage the upholstery or stitching.
Removes mold & mildew stains on contact Blocks stains from reoccurring Does NOT contain bleach Fresh scent Works on ALL water-safe surfaces, including vinyl & fabrics Mold & Mildew Cleaner & Blocker with Trigger Sprayer – 32oz 303 Mold & Mildew Cleaner + Blocker quickly and safely cleans and removes tough mold and mildew stains from virtually any water-safe surface.
Not only does this product CLEAN unsightly mold and mildew stains that have already formed, it will also help PREVENT mold and mildew stains from re-occurring on the treated surface. Unlike other mold & mildew cleaner products on the market, this product does NOT contain bleach, and will leave behind a fresh scent, with no strong odors to worry about during or after use.
Works safely on vinyl, plastic, painted surfaces and even safe enough for use on fabric! Features: Quickly removes mold & mildew stains on contact Blocks mold & mildew stains from re-occurring Does not contain bleach, leaves behind a fresh scent Works on ALL water-safe surfaces, including vinyl & fabrics WARNING: This product can expose you to chemicals including Diethanolamine which is known to the State of California to cause cancer, and Sulfur Dioxide which is known to the State of California to cause reproductive harm.
I first bought this for $15 in the store size spray bottle. I read about its uses online and then put it through the test. I drove part-time Uber/Lyft Suv Lux. I maintain my own cars and it’s a pain carrying around several different spray bottles, one for the dash, one for the leather, tires, exterior plastics when you are a perfectionist in keeping your car in brand new shape.
With that in mind, I also read about the uses on serpentine belts, all of the tires, sidewalls and tread, soft rubber door seals. I tried it on everything. After I bought the small bottle, I bought two gallons on Zoro and they lasted me over 3 years ( well worth it).
The end result of a 2016 Tahoe Lt with 72,000 miles on it ( 3 years at this point which I bought brand one-year, I know I’m repeating myself) and it still looks like new. As I rotated the tires, I sprayed this stuff on the tread, sidewalls (factory junk Uniroyals got close to 60,000 miles on them).
I have sprayed the door seals, no cracks and still supple. All the interior vinyl and leather as new. I even sprayed the serpentine belt in the engine ( difficult to due properly since I didnt take it off and you need to get it on top and the bottom) but it still looks brand new with no wear in any manner.
You can throw away 4-5 products and just buy one. I cant tell you how many compliments I get despite having over 600 plus rides including my own family trips and abuse of this SUV. I have seen plenty of other same year Tahoes and Suburbans and the interior looks nothing like mine.
My only complaint. there is no company that makes a decent chemical resistant spray bottle. I even buy the heavy duty ones and they all leak after several months of use. Too bad 303 didn’t make a bottle as good as the product.
Shake the gallon real good before refilling your spray bottle and shake the spray bottle before use also.
Learned of 303 Aerospace when researching dry rot after 5 yr old tires (car not garaged) wouldn’t pass inspection because of cracks in the treads. Numerous more knowledgeable sites I found recommended 303 and talked about how many of the well known silicone products were actually bad for rubber and some could accelerate dry rot.
I don’t use the silicone products because hate the slick, shiny, greasy-feeling surface they leave. 303 leaves a surface finish that looks rich, conditioned, not shiny, newer than before. I’ve used on car tires, plastic/vinyl car trim, plastic planters, plastic outdoor chairs, certain painted lawn decor.
After use, surfaces are much easier to clean, ex. used to have to use mild abrasive cleanser to get marks off plastic lawn chairs. UV protection important for outdoor plastics and rubber. Wish could find 303 in local stores, will keep sending away for in the meantime.
I have been using 303 Aerospace Protectant on my boat vinyl ever since discovering it in the hot tub community where it’s used to keep covers looking good. It does a great job keeping vinyl looking new.
I’ve used it on 5 boats now in the last 20 years, and the oldest one is nearly 30 years old. The vinyl still looks very good. Highly recommend!.
When it comes to cleaning products for mold, there are a few things you need to keep in mind. First and foremost, you need to make sure that the product you’re using is designed specifically for mold.
There are a lot of cleaning products on the market that claim to be able to kill mold, but not all of them are effective. Secondly, you need to make sure that you’re using the product correctly. Some products require you to dilute them before using, while others need to be applied directly to the moldy surface.
Follow the instructions on the product label carefully to ensure that you’re using the product correctly. Finally, be sure to ventilate the area well while you’re using the mold cleaner. Mold spores can be released into the air when you’re cleaning, and you don’t want to breathe them in.